#Savage model 24 over under 22 410 price full#

#Savage model 24 over under 22 410 price full#

410 would take up to 3вЂіshells and had a full choke. 22 barrel would accept S, L and LR rimfire rounds and the same length. Taking the Stevens combo gun, Savage retained the concept of a standing breech, break open rifle over shotgun combination gun, which utilized a rebounding hammer and rear pushing extractors. The same year the Stevens 22-410 went out of production, the Savage 24 was introduced. Savage had been (and still is) the parent company of Stevens since 1920, making it easy to see the import of the Savage 24вЂ™s concept. In 1950, the gun went out of production with Stevens. The Army Air force ordered 15,000 of them for use as aircrew survival rifles with a Tenite (an early thermoplastic) stock. Stevens put the handy little marvel into production in 1938 with the appropriate moniker of the Model 22-410. 22 rimfire rifle barrel with a single sight, hammer, and trigger. Note position of fore-end spring (O) in relation to hook on underside of barrel.This firm came about with a combination gun with a smoothbore. Swing barrels upward, locking barrels to frameДЈ When reassembling fore-end (U) to underside of barrei (A), place rear of fore-end iron head (V) in position shown against front edge of frame. hook cut-out at forward end of barrel lug onto hinge pin in forward end of frame as shown. Reassemble in reverseДў When reassembling barrel (A) to frame (1). Fore-end parts are easily removed by removing screws S and T. Note: extractor lever spring (J) is inserted in barrel lug between front end of lug and arm on extractor lever (L). Drift out extractor lever pin (M) and remove extractor lever (L) from lug under barrel. 410 extractor (G) and stem (H) from breech end of barrel. 22 extractor (E) and spring (F) from breech end of barrel. Fore-end iron head screws (2)ДЎ After removing fore-end (U) from underside of barrel (A) and separating barrel from frame, loosen extractor screw (D) and withdraw.

Firing pins are retained in frame by screws (10 & 11) which are staked at the factory which makes them rather difficult to remove. Major parts are retained in frame by pivot pins. Slide buttstock off frame to rear.ДЇurther disassembly of frame and lock parts is not recommended and should be unnecessary for normal cleaning purposes. Unscrew stock bolt (2) through hole in butt of stock. To remove buttstock, unscrew both butt-plate screws and remove buttplate. Unhook barrel lug from hinge pin at forward end of frame. Move top snap (16) to side and openД«reech by tipping barrel downward. 1) grasp it at the tip and pull away from barrel. 22 Winchester Magnum Rimfire cartridge and with the same choice of shot-shell chamberings as the DL. 22 long rifle cartridge and is optionally available with shotgun barrel chambered for either the 20-ga. In 1962, the Model 24 was introduced in DL and MDL types, with fire selector button on left side of the frame rather than on the right as on the original model.

Magnum Rimfire cartridge was introduced in 1959, the Model 24 was made available in this caliber also. In 1950 a slightly improved type with walnut stock assembly and somewhat heavier barrel replaced the original model. Air Force purchased 10,000 of these combination guns with Tenite stocks for issue to aircrewmen as survival weapons.Д¬ommercial production was resumed in 1945. Guns produced initially had walnut stocks and fore-ends, but stock assemblies of Tenite plastic were later made standard. 22 long rifle cartridge and the 3' length of the. Stevens Arms Co., a wholly owned subsidiary of the Savage Arms Corp. 22-.410 over-under combination rifle and shotgun was first offered in 1939 by the J.